Le Forum des Galaxy S2, S3 et du Galaxy Note

Je tourne avec la FukLagRomow sous abyss 3.0 en alternance avec la Checkrom aussi sous abyss. Ces deux Roms sont très fluides et peu gourmandes et très honnêtement pas de FC.
Repartir peut-être d'une Rom stock, installer un de ces deux Rom customs et redonner des nouvelles

Changelog v3.1:

ARM: vfp: use -mfloat-abi=soft to build vfp
vfs: new helper - d_make_root()
pm-hotplug: screen_off event is more likely
cpuidle: Stop spamming the kernel message buffer when enabling AFTR
nohz: Fix update_ts_time_stat idle accounting
Some wifi changes to prevent very frequent wifi wakelocks
Some more RAM undervolt
s3cfb_mdnie.c = Bypass DE SHARPNESS, DE TH, CS Gain
Re-worked ondemand governor and merged with ondemandx and intellidemand governors
Re-worked SmartassV2 and Interactive governors
Removed Interactivex, Ondemandx, Intellimand, Savagedzen governors
Changed value in Conservative governor
Some defaults (hotplug parameters and governor defaults) are tweaked to provide better battery life
Changed Value in XZ compression

Allez seb ...au boulot !

EDIT sebfar : j'arrive

Je vais faire un peu mon boulet, mais j'aurais besoin que l'on m'explique brièvement ce qu'apporte ce kernel, j'ai beau lire le changelog, j'y comprend pas grand chose

Jérôme M.

[sebfar]

Changelog v3.2:

cputimer: Cure lock inversion
mm: readahead page allocations are OK to fail
mm: page allocator: initialise ZLC for first zone eligible for zone...
mm: page allocator: reconsider zones for allocation after direct reclaim
memcg: clear mm->owner when last possible owner leaves
memcg: fix get_scan_count() for small targets
memcg: fix percpu cached charge draining frequency
sdio: optimized SDIO IRQ handling for single irq
fs: improve scalability of pseudo filesystems
ARM: dma-mapping: free allocated page if unable to map
vfs: micro-optimize acl_permission_check()
Removed mc1n2_voodoo module (no more necessary)
Several other fixes
Change compiler optimizations

[sebfar]

Changelog v3.3:

Changed conservative governor
Changed default governor ondemand with sampling rate of 100000. use setcpu or scripts to lower it (or try conservative governor) if you prefer performance over battery life.
Changed lulzactive governor so that it uses idle notifier + some other tiny tweaks
Added Hotplug Governor
Changed Wifi drives
GPU speed step increased to (200MHz, 300Mhz, 400Mhz) from (160MHz, 267Mhz, 300Mhz)
Nls_utf8 module integrated into the kernel
Ashmem and alignment fix
Allow_cpu_alignment enabled
Others several fix

[sebfar]

Changelog v3.4:

Fixed the bug which prevented using ubuntu and was causing some random reboots
Code cleanups (removed cleancache, some jrcu configs etc)
Enabled cpu alignment again
Enabled some more networking options in config (ipip, l2tp etc)
Modified GPU frequency setting code a bit. if you use voltage control app or a script to set the second GPU step frequency higher than the third, the third frequency is disabled.
Tiny tweak for ondemand governor
Set topoff current in battery driver to 100mA (stock value is 200mA) to ensure that the battery is fully charged before the charger circuit stops charging.
Added Entropy512′s changes to sec_battery driver to show battery charging (not discharging) current in currentwidget (thanks to Entropy512).
Added BFQ i/o scheduler V3r2

[sebfar]

Changelog v3.5:

Replaced the recovery with Hyperdroid Redpill Recovery. (Thanks to Hyperdroid team and Redpill kernel developer(s)). This recovery can also mount both internal and external sd.
Changed some mali internals (set staycounts for steps to: 0-1-1 and down threshold for second step is set to 35).
Enabled TINY_SHMEM (should improve performance)
Revisited Ondemand and LulzactiveV2 Governors
Tweaked Conservative and SmartassV2 governors a bit more
Added AbyssPlug and Weathley Governors
Removed jrcu leftover
Added new rcu patches
MM: slub: Default slub_max_order to 0
MXT540E: Added Touchscreen fix
Modified gamma table
Others little fix

[sebfar]

Changelog v3.5b:

Added NoMoarPowah compatibility
rest like v3.5

Moi aussi v faire mon relou:

Apres une petite recherche je n'ai pas trouvé d'explication sur les KERNEL : PDA ou kernel : c'est le système d'exploitation du SGS2 ça OK.

Mais je peux donc flasher sans que ça réinstalle ma rom actuel ? et donc bénéficier d'améliorations ?

Au mieux le quel me conseilleriez vous ?

D'avance merci

[sebfar]

Changelog v3.5c:

Re-inserted logger module into the kernel for compatibility with various apps
rest like v3.5 + v3.5b